Filler Metal 12.4 Procedure Specification. 13 ‘Study Guide for API Standard 1104, Twentieth Eaition AWS API-M:2008 Section 12- 12.1 Acceptable Processes Mechanized 12.2 Procedure Qualification. 3 11.3 Liquid Penetrant Test Method 3 11.4 Ultrasonic Test Methods. 10-1 11.1 General tel 11.2 Magnetic Particle Test Method. 9.7 Visual Acceptance Standards for Undercutting.
Radiographic Testin 9.4 Magnetic Particle Testing. 7.11 Pre- and Postheat Treatment 9.1 General 9.2. Roll Welding 7.10 Identification of Welds. 7.5 Weather Conditions 7.6 Clearanc sn 7.7, Cleaning Between Beads.
Use of Lineup Clamp for Butt Weld WW 74 Bevel. Records 4 7.1 General ve se se seems 7.2. 6-2 AWS API-M:2006, Section Section 7 Design and Preparation of a Joint for Production Welding Section 8 Inspection and Testing of Production Welds Section 9 Acceptance Standards for Nondestructive Testing Section 10 Repair and Removal of Defects Section 11 Procedures for Nondestructive Testing ‘Study Guide for API Standard 1104, Twentieth Ecition Radiography Bur Welds Ol. rt) 6.2 Single Qualification 6-1 6.3 Multiple Qualification, 6-2 64 Visual Examination. 5.7 Welding of Test Joints-Fillet Welds 5.8 Testing of Welded Joints-Fillet Welds. Procedure Specification 5.4 Essential Variables.
Definition of Documents ae z Less Than or Greater Than? : 11 Other Definitions ‘The Meaning of Quality. LeJeune Road, Miami 3126 ‘Study Guide for API Standard 1104, Twentieth Edition Table of Contents Section Introduction: How to Use API 1104 Section 1 General Section 2 Referenced Publications Section 4 Specifications Section 5 Qualification of Welding Procedures for Welds Containing Filler-Metal Additives Section 6 Qualification of Welders [AWS APL-M:2006 ‘Study Guide for API Standard 1104-Foreword ‘ii List of Tables. Exercise questions and answers are provided for each topic. Material is provided for each of the 13 sections of the standard and both appendices. It is intended that all work performed in accordance with this standard shall meet or exceed the requirements of this standard.AWS API-M:2006 Study Guide for API Standard 1104 Welding of Pipelines and Related Facilities TWENTIETH EDITION American Welding Society AWS API-M:2006 Study Guide for API Standard 1104 Welding of Pipelines and Related Facilities TWENTIETH EDITION Published by American Welding Society Education Services Abstract ‘This study guide contains information on the use of API Standard 1104, Twentieth Edition, which will assist in the student prepare for the using the standard as wel as preparing for code-related examinations. This standard also covers the procedures for radiographic, magnetic particle, liquid penetrant, and ultrasonic testing, as well as the acceptance standards to be applied to production welds tested to destruction or inspected by radiographic, magnetic particle, liquid penetrant, ultrasonic, and visual testing methods. The welds may be produced by position or roll welding or by a combination of position and roll welding. The welding may be done by a shielded metal-arc welding, submerged arc welding, gas tungsten-arc welding, gas metal-arc welding, flux-cored arc welding, plasma arc welding, oxyacetylene welding, or flash butt welding process, or by a combination of these processes using a manual, semiautomatic, mechanized, or automatic welding technique or a combination of these techniques. It applies to both new construction and in-service welding. This standard covers the gas and arc welding of butt, fillet, and socket welds in carbon and low-alloy steel piping used in the compression, pumping, and transmission of crude petroleum, petroleum products, fuel gases, carbon dioxide, and nitrogen, and, where applicable, covers welding on distribution systems.